A datalogger is a device used to record and store the output of one or more sensors. In some cases, the datalogger interprets the electical signal from the sensor and converts it to units. In cases where a smart sensor provides digital output, the datalogger simply records the data. Early dataloggers were strip chart recorders that recorded measurement data onto paper. Over time, dataloggers evolved to store data digitally on various types of media. Today, data is typically stored on modern flash memory and often transmitted via a variety of telemetry methods.
Note: Similar terms for "datalogger" include "data logger," "data recorder," "data acquisition system," and "RTU" (remote terminal unit). Which term is used often varies by industry or discipline.
Today, a wide range of devices are referred to as "dataloggers," and they can vary greatly in their functionality. For example, one datalogger may be packaged together with a sensor for a single application-specific purpose, such as measuring temperature. Another datalogger may be a general-purpose device that is used in many different applications to log data from multiple sensors of varying types.For the purpose of this discussion, our focus will be on general-purpose dataloggers.
Most modern, general-purpose dataloggers are microprocessor-controlled electronic devices that can interface directly with a variety of sensors to do the following:
In addition to their measurement and monitoring functions, some dataloggers can trigger an alarm or notification, as well as control an external device, in response to any of the following: a specific, measured site condition; time of day; or event. For example, a datalogger may be programmed to respond to a measured rise in water level by closing a floodgate and sending a notification to personnel.
The following illustration depicts the most common parts of a general-purpose datalogger:
A data acquisition system consists of multiple electronic devices that act together to serve the primary purpose of collecting measured data. The general-purpose datalogger is often considered the brain of a data acquisition system, but it is only one of the interfaced components used in the process of acquiring, recording, transmitting, and analyzing measurements. These components may include the following:
A facility may individually select each of their data acquisition system’s components, thereby creating a customized solution that will meet their specific needs.
The datalogger can be programmed to scan the sensors of the data acquisition system repeatedly after a specified interval has passed (the scan rate), under specified conditions, or after the occurrence of a particular event type (such as rainfall). A sophisticated datalogger can receive the electrical signals from the sensors, perform any programmed calculations, convert the data as necessary to other units of measurement, and store the resultant data in the datalogger’s memory.
The datalogger’s acquired data and calculated values will need to be transferred to a PC or other device for increased access, sharing, analysis, and reporting. A variety of methods can be used to accomplish this, including communication peripherals with onsite and telecommunication options.
While many general-purpose dataloggers are designed to be installed in protected environments, some are specifically developed for extreme environmental conditions. These extreme environments include mountainous terrain, deserts, jungles, mines, oceans, and glaciers. A datalogger is typically left unattended for lengthy periods to automatically process and record measurement data from a variety of sensors until the monitoring period ends, which may be decades later.
The universal application of dataloggers in climates across the world, from the poles to the equator, is often attributed to their ruggedness, compact size, wide operating temperature ranges, low power usage, and capability of operating in diverse environments. The universality of sophisticated dataloggers is further enhanced by their many connection types and programmable inputs, which enable them to measure almost any commercially available sensor. Because dataloggers provide a comprehensive, accurate, and reliable depiction of the monitored conditions without the need for site visits, they are an indispensable tool for unattended, long-term monitoring and control for numerous industries and applications.
In this illustration, several different types of general-purpose dataloggers are displayed. These different types enable dataloggers to accommodate a wide variety of measurement applications.
While dataloggers can be compared and contrasted on many different levels, the following are some primary characteristics that may be helpful for you to be mindful of:
These characteristics are discussed briefly in the following sections.
In general, the size of the datalogger is dictated by the number of inputs and outputs (I/O) and connection points. Smaller dataloggers have a smaller footprint requirement, which enables a facility to use a smaller enclosure that is less expensive and less noticeable. A smaller datalogger, however, is limited in functionality because fewer sensors or peripherals can be connected to it.
Even if a datalogger isn’t housed inside an enclosure, there may be space restrictions at the site that prohibit the use of a larger datalogger.
Although some manufacturers may not conform to this convention, the published operating temperature range typically refers to the range at which the datalogger will operate within its specified measurement accuracy. Measurements may still be recorded outside of this temperature range, but the accuracy of the measurement may be in question, and the datalogger may not perform as expected. Other operational errors may also occur.
Some dataloggers only have a standard operating temperature range, whereas other dataloggers may offer an extended temperature range option that is useful in environments with more extreme temperatures.
The wiring panel of a datalogger provides terminals for connecting sensors. These terminals enable the datalogger to measure, communicate with, and power the sensors.
Dataloggers vary both in the quantity and types of input connections they offer. A datalogger with fewer sensor connection options:
In contrast, a datalogger with more connection options:
Some dataloggers can scan almost any sensor with an electrical response—whether the sensor’s signal output is voltage, current, pulse, digital, or serial. However, for the datalogger to interpret the sensor’s signal, the signal output from the sensor must be compatible with the datalogger input terminal to which it is connected. Typically, the instruction manual of a sensor provides information regarding which type of datalogger connection is required, as well as how to wire the sensor to the datalogger.
The following are some common terminal types used to connect dataloggers with sensors:
These terminal types are discussed briefly in the following sections.
Analog inputs refer to both voltage and current inputs, and they are often used with any of the following:
Pulse counters are used by the datalogger to measure switch closures, low-level ac sine waves, or high-frequency pulses. Pulse counters sum the number of counts over each execution interval (scan rate), allowing variables such as rpm, velocity, flow, and rainfall intensity to be determined.
Pulse counters are often used with any of the following:
Switched voltage excitation outputs are used with sensors that measure voltage resistance. These outputs provide programmable voltage excitation for resistive bridge measurements by switching the voltage on and off. The bridge measurements are the ratio of the voltage output to the excitation voltage, eliminating any errors in the excitation voltage.
By default, digital I/O ports are configured as binary inputs to perform functions such as detecting status or reading SDM peripherals. In addition, each port can be individually programmed as a control output to physically control an external device.
RS-232, RS-422, and RS-485 ports are used to connect the datalogger to smart serial sensors and communication devices.
These terminals can be regulated or unregulated power sources for sensors and other peripheral devices.
The 12 V terminal is generally used as an unregulated continuous power source for sensors and other devices.
A switched 12 V terminal is used to power devices such as sensors that only require power periodically. These terminals are controlled by the datalogger to power the sensor only during measurements.
The wiring panel of a datalogger also provides terminals for connecting power supplies, communication peripherals, and external control devices. The input and output connections on the wiring panel enable the datalogger to communicate with and power various peripherals.
The following are some common terminal types used to connect dataloggers with other peripherals:
Continuous analog outputs provide voltage levels to peripheral devices or proportional controllers. This allows the datalogger to have control over other devices, including digital displays and controlled devices such as proportionally controlled gates.
Dataloggers often are used as measurement devices within a SCADA (supervisory control and data acquisition) system. The continuous analog outputs can then be used to send data directly from the datalogger to a PLC (programmable logic controller).
These ports are used to communicate with other expansion devices that are unique to the specific manufacturer.
These terminals are used to connect the datalogger to an external power supply. Because these terminals can be easily removed, they provide a quick-disconnect option.
A datalogger may allow the expansion of its input and output capabilities using expansion modules, such as Synchronous Devices for Measurement (SDMs), and multiplexers. These add-on modules and multiplexers enable the datalogger to measure more sensors by increasing the number and type of connections available beyond what the datalogger provides on the wiring panel. Control modules increase the number of devices that can be controlled by the datalogger.
Accuracy is the ability of a measurement to provide a result that is as close as possible to the actual value. For example, a datalogger that produces a measurement within ±0.1 of the actual value is said to be more accurate than a datalogger that produces a measurement within ±0.5 of the actual value. Accuracy is often listed by the manufacturer at a specific temperature (typically 25°C). Some manufacturers will specify accuracy over a temperature range.
Precision is the amount of agreement between repeated measurements of the same quantity. For example, a datalogger that produces 10 measurements of the same sample within ±0.1 of each other is said to be more precise than a datalogger that produces 10 measurements of the same sample within ±0.8 of each other.
In measurements, resolution refers to the smallest change in a quantity that can be detected. For example, if one datalogger detects a difference to the nearest tenth of a millivolt, that datalogger is said to have higher resolution than another datalogger that detects a difference to the nearest whole millivolt.
Depending on the manufacturer, some dataloggers cannot differentiate between the interval at which they scan (measure) the sensor and the interval at which they record the measured value. (The two rates are treated as being the same.) The datalogger will scan the sensor based on a selected record interval, and every measured parameter is recorded with each scan.
In contrast, a sophisticated datalogger can be programmed to scan a sensor based on a time scan rate, under specified conditions, or in response to an event. Programmed scan rates can vary greatly, depending on the datalogger model, and may range, for example, from once every few hours to 100,000 times per second (Hz). It is important to note that every single measurement from the scans does not need to be recorded. For example, if a sensor is scanned every five seconds (the scan rate), only an average reading for a 15-minute period (the sample rate) may need to be recorded.
The maximum scan rate is the highest frequency at which the datalogger scans the sensors. For example, dataloggers may range from a maximum scan rate of 1 to 100,000 Hz.
A datalogger with a slower maximum scan rate may be less expensive, but the rate at which parameters (such as rainfall) can be measured and recorded is limited. Consequently, less measurement data is available for a specified period compared to the amount of data that could be acquired during the same period using a datalogger with a faster maximum scan rate.
To transfer data from a datalogger to a central location, such as a base station PC or cloud-hosted database, a datalogger may have integrated communication capabilities, or it may be able to interface with an external communication device. These devices may support a hardwired connection (such as Ethernet), wireless cellular, or Wi-Fi. Various other communication options such as satellite or frequency-hopping spread-spectrum radios are also used.
A datalogger may be equipped to control external devices—in addition to providing advanced measurement and monitoring capabilities. As a control mechanism, a datalogger can be programmed to activate a device at a preset time, in response to a measured condition, or in response to an event. Dataloggers can activate or shut down motors, gates, pumps, purifiers, valves, injectors, etc. For example, if a temperature level rises above a predetermined maximum, the system can activate HVAC equipment. Moreover, control functions can be based on multiple conditions or events, such as deciding to initiate or suspend air exchange based on time of day, outside temperature, and/or inside temperature.
Some dataloggers offer very limited programming flexibility such that the user is restricted to preset functions that the datalogger can handle. Other dataloggers use a microprocessor with a built-in programming language and instructions to enable the user to create and run new, customized programs. These dataloggers offer the user more control and the possibility to program cross-channel computations. The following is an example snippet of code from a datalogger’s programming language:
'Declare Variables and Units Public BattV Public PTemp_C Public Temp_C Units BattV=Volts Units PTemp_C=Deg C Units Temp_C=Deg C 'Define Data Tables DataTable(OneMin,True,-1) DataInterval(0,1,Min,10) Average(1,Temp_C,FP2,False) EndTable 'Main Program Begin Prog 'Main Scan Scan(1,Sec,1,0) 'Datalogger Battery Voltage measurement 'BattV' Battery(BattV) 'Datalogger Panel Temperature measurement 'PTemp_C' PanelTemp(PTemp_C,60) 'Type T (copper-constantan) Thermocouple measurements 'Temp_C' TCDiff(Temp_C,1,mv34,1,TypeT,PTemp_C,True,0,60,1,0) 'Call Data Tables and Store Data CallTable OneMin NextScan EndProg
Some dataloggers can perform basic processing of the data collected from the system’s sensors. Examples include the calculations of daily minimums, maximums, averages, totals, or other statistical values. Moreover, parameters such as the following can be calculated using the data provided by sensors: density altitude, dew point, evapotranspiration, heat index, and wind chill.
By providing onsite statistical and mathematical processing, the datalogger can record just the calculated values rather than all the individual measurements. This provides the needed information in fewer numbers, simplifying the data analysis or review process. Because the frequency of recorded measurements is decreased, the quantity of data stored is reduced significantly. By reducing your quantity of stored data, you can prolong the time before your datalogger’s memory becomes full and needs to be downloaded, as well as decrease the amount of data that is being transmitted via the cellular or other wireless communication devices.
The communication protocol is the system of rules that manages how data is exchanged between the datalogger and other devices. This includes communication between the datalogger and external measurement devices within the data acquisition system, between the datalogger and other dataloggers within a network, and between the datalogger and the PC or server. The protocol is particularly important when integrating a datalogger with an existing system to ensure that the system devices and the datalogger can all use the same protocol to communicate with each other. The communication protocols may be proprietary to the manufacturer of the datalogger, external devices, or software. These protocols may also be developed and managed by third-party organizations such as Modbus, DNP3, SDI-12, or FTP.
Some dataloggers have an integrated or detachable keyboard display that includes a screen and keypad. The display enables the user to view measured data, generally in both real-time and historical formats.
The keypad functions of the display may also provide the user with the ability to program, configure, and analyze the datalogger while in the field—without the need for other external communication devices such as laptop computers, smartphones, or tablets.
Knowing how frequently the sensors are scanned (scan rate), as well as how frequently data measurements and/or calculated values are recorded (sample rate), provides helpful information in determining how long a datalogger can record data before the memory capacity becomes full and requires downloading. Unless the datalogger has a display screen, data that is stored in the internal memory of the datalogger must be physically transferred to a PC or other web-browser-enabled device for visualization, analysis, sharing, report generation, and permanent storage.
The internal data memory, program, communications, and operating systems are stored in SRAM or RAM memory. Depending on the type of memory storage used, this memory is backed up by an internal lithium battery. In the event of power loss or when the datalogger is not connected to an external power supply, the battery maintains the memory and clock.
If a datalogger’s memory capacity is not sufficient to meet a facility’s scan rate and sample rate needs, an external data storage device may be purchased and used as well. Using an external data storage device provides a redundant data resource if the memory on the datalogger becomes full, resulting in data loss.
Selecting a datalogger is an important decision that requires careful consideration. For assistance with the selection process, review the detailed Purchase Considerations section.
Number of FAQs related to Dataloggers & Sistemas de Coletores de Dados: 19
Expandir todosRecolher todos
The CR1000, CR800, CR850, and CR3000 can accept PakBus connections from multiple terminals simultaneously, provided that all of the connecting nodes have unique PakBus addresses.
Yes. All Campbell Scientific dataloggers currently have nonvolatile memory. Nonvolatile memory was added to the CR10X in 1996. All datalogger models introduced since then have included nonvolatile memory.
Nonvolatile memory is reliant on the 3 V lithium battery inside the datalogger. As long as this internal battery has a charge above 3 V, no data should be lost if the datalogger loses power.
Campbell Scientific dataloggers do not directly support LonWorks, but an industrial protocol converter can be used to add a datalogger to a new or existing LonWorks network. The protocol converter sits between the datalogger and the network, and it converts LonWorks requests to a protocol supported by the datalogger, such as Modbus, DNP3, SNMP, or others.
Campbell Scientific dataloggers do not directly support BACnet, but an industrial protocol converter can be used to add a datalogger to a new or existing BACnet network. The protocol converter sits between the datalogger and the network, and it converts BACnet requests to a protocol supported by the datalogger, such as Modbus, DNP3, SNMP, or others.
For more information about BACnet, see the “BACnet to Modbus/Modbus to BACnet Protocol Conversion” application note.
Yes. The datalogger can control power to external devices under program control. For more information, see the “Decisions, Decisions, Decisions…” article.
To turn a generator on and off, a solid state relay with a load capacity that matches or exceeds the power of the generator is needed. The relay is controlled by one of the control ports on the datalogger.
Yes. We have developed programs for controlling devices and collecting data remotely. Program examples and datalogger wiring are provided in the 10164-L instruction manual. Contact Campbell Scientific for more information.
Yes, but there is the potential for explosive hydrogen gas from a rechargeable battery to build up inside the airtight, waterproof enclosure. Care should be exercised in choosing a power supply for applications where the enclosure must be waterproof. Contact Campbell Scientific’s technical support for more information.
Possibly. If a voltage greater than 16 Vdc is applied to the wiring panel, it could damage the input and result in inaccurate measurements.
Additionally, in some cases the sensors can be damaged if they are wired to the wrong channels. If a sensor, wired into an analog input channel, has an output of more than 5 Vdc, measurements on adjacent analog input channels may be upset. For example, the maximum full-scale range on the CR5000 is ± 5Vdc.
Dataloggers, which may also be referred to as Measurement and Control Units (Systems) or Microloggers, are the heart of a data acquisition system. They measure sensors at a specific scan rate, process data, store the data, and initiate telecommunication. Our dataloggers also have control capabilities allowing them to respond to specific site conditions by opening flood gates, turning fans off/on, etc.