Services Available | |
---|---|
Repair | No |
Calibration | No |
Free Support | No |
In September 2005, the CR205 Datalogger was replaced by the CR206 Datalogger. The CR206 has improved communication capability. The CR205 can be used within a CR206(X) network, but the CR206(X) needs to be in the transparent mode. Contact one of our application engineers for details.
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Product | Compatible | Note |
---|---|---|
014A-L | ||
03002-L | ||
034B-L (retired) | ||
05103-45-L (retired) | ||
05103-L | ||
05106-L (retired) | ||
05305-L | ||
107 | ||
108 | ||
109 | ||
109SS | ||
110PV-L (retired) | ||
19227 | ||
237-L (retired) | ||
255-100 | ||
27014 | ||
27106T-L | ||
43347-L | ||
CMP11-L (retired) | ||
CMP21-L | ||
CMP6-L (retired) | ||
CS100 | ||
CS106 | ||
CS15-L (retired) | ||
CS215-L (retired) | ||
CS300-L (retired) | ||
CS410-L (retired) | ||
CS431-L (retired) | ||
CS450-L (retired) | ||
CS455-L (retired) | ||
CS460-L (retired) | ||
CS470 (retired) | ||
CS471 (retired) | ||
CS475A-L (retired) | ||
CS475-L (retired) | ||
CS511-L | ||
CS525-L (retired) | ||
CS616 | ||
CS625 (retired) | ||
CS650 | ||
CS700H-L | ||
CS700-L | ||
CSAT3 (retired) | ||
CSIM11-L | ||
CSIM11-ORP-L | ||
ENVIROSCAN (retired) | ||
HMP45C-L (retired) | ||
HMP60-L | ||
LI190SB-L (retired) | ||
LI200X-L (retired) | ||
LWS | ||
OBS-3+ (retired) | ||
OBS300 (retired) | ||
SEN12512 (retired) | ||
SR50A-L (retired) | ||
TB4-L | ||
TB4MM-L | ||
TE525-L | ||
TE525MM-L | ||
TE525WS-L | ||
WINDSONIC4-L | ||
WXT520 (retired) |
Product | Compatible | Note |
---|---|---|
LoggerNet | Version 2.1 or higher | |
PC200W (retired) | ||
PC400 | Version 1.0 or higher | |
PCONNECT (retired) | Version 3.0 or higher | |
PCONNECTCE (retired) | Version 2.0 or higher | |
Short Cut | ||
VISUALWEATHER - Retired (retired) | Version 2 or higher |
The CR205's internal spread spectrum radio can transmit data to other CR205 loggers or RF400 radios. It can also communicate with CR206(X) loggers, RF401 radios, or RF430 radios if they are set to the transparent mode. Certain CR205 settings must match the radio's settings for communications between the data logger and radio to be successful. The factory default settings of these devices might not match; therefore, they may need to be reconfigured before communications can take place.
The CR205 can communicate with a PC via direct connect, NL100 Ethernet interface, MD485 multidrop modem, and digital cellular modems. Data can be viewed on the CD295 DataView II display, Archer-PCon Field PC, or a user-supplied PDA (PConnect or PConnectCE software required).
The CR205 is not compatible with SDM devices and multiplexers.
The CR205 can measure a variety of sensors including SDI-12 sensors and 4 to 20 mA sensors. It cannot make differential measurements and is not compatible with the freezing-rain/ice, fuel moisture/temperature, geographic position, present weather, soil heat flux, soil matric water potential, and strain sensors listed on our price lists.
Applications with minimal power requirements can use the ENC200 enclosure to house the data logger and the #16869 sealed rechargeable battery. The ENC200 cannot house a barometer or a battery that is larger than the #16869. However, an ENC10/12 or ENC12/14 enclosure is adequate for most CR205-based systems.
The CR205 uses an external power supply and has a built-in regulator. When connected to the on-board charging circuit, the sealed rechargeable battery should be 7 Ahr or smaller. Using larger batteries with the data logger's built-in charger may result in excessive PC board heating. This is especially a concern when the battery is deeply discharged or failing with a shorted cell. Campbell Scientific also recommends that solar panels be 10 W or less and wall chargers be 1 A or smaller.
A/D Converter | 12 bit |
Scan Rate | Once per second (maximum) |
Single-Ended Analog Channels | 5 (individually configured) |
Analog Voltage Range | 0 to +2500 mV |
Measurement Resolution | 0.6 mV |
Excitation Channels | 2 (programmable for either +2.5 or +5 volts) |
Switched Battery Port | 1 |
Pulse Count Channels | 2 |
Control Ports | 2 |
Battery Voltage Range | 7 to 16 Vdc |
Communications | RS-232 |
Special operating system that supports ModBus communication and SDI-12 sensors . Also included is the Compiler and CRBasic Editor support files for the CR2xx dataloggers.
Use of this file will update the datalogger compiler and CRBasic Editor support files.
Note: Not to be used with the CR200X series.
Includes: MODBUS Instructions, SDI12Sensor, WindVector
Excludes: GOES Instructions, SerialInput, ETO, SendData, & LoggerIdentify
Special operating system that supports serial sensors, SDI-12 sensors, and sending data to another PakBus device. Also included is the Compiler and CRBasic Editor support files for the CR2xx dataloggers.
Use of this file will update the datalogger compiler and CRBasic Editor support files.
Includes: SerialInput, SendData, SDI12Sensor, WindVector
Excludes: GOES Instructions, ETo, MODBUS Instructions, LoggerIdentify
A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.
Supported Operating Systems:
Windows 11 or 10 (Both 32 and 64 bit)
Short Cut creates simple programs for our CR200-series, CR300-series, CR510, CR500, CR10(X), 21X, CR23X, CR6, CR800, CR1000(X), CR1000Xe, CR3000, CR5000, CR9000X and GRANITE dataloggers. Both mixed array and table data operating systems are supported. Short Cut also supports our ET106, ET107 and MetData1 weather stations. The newest version includes the latest sensor files.
Default operating system loaded into the datalogger at the factory. Also included is the Compiler and CRBasic Editor support files for the CR2xx dataloggers.
Use of this file will update the datalogger compiler and CRBasic Editor support files.
Includes: ETo, WindVector, LoggerIdentify
Excludes: GOES Instructions, SDI12Sensor, SerialInput, MODBUS Instructions, SendData
Number of FAQs related to CR205: 3
Expandir todosRecolher todos